OsstellConnect

Osstell Beacon
• To find your registration code, please make sure that you have already installed the Beacon Gateway. If you have not installed it yet, please navigate to your clinic in your account, click the instruments tab and download the gateway. Install it.
• Take your instrument in hand. It is now connecting to OsstellConnect and you should see a symbol animating. Please note that it can take a few seconds.
• When connected, the symbol stops animating.
• The registration code is now displayed on the lower screen of your instrument.

Osstell IDx
• When turning on your Osstell IDx for the first time, you will be prompted to select language, time zone, date and time.
• After that, you will need to set up a 4-digit pin code and a backup password. The backup password is needed when restoring to a backup, so please note it down and save it in a safe place.
• Your registration code is now displayed on your Osstell IDx.

You can find the serial number on the back of your instrument.

Navigate to your clinic in your account. Select the instrument tab. Click on Download firmware.
Download instructions:

• Wait for the download to complete (could take a while depending on your connection)

• Copy the .m2f binary file to a USB memory stick

• Insert the memory stick in your IDx while it is running

• Follow instructions on the IDx display

Note: you cannot open or view the .m2f file
You can also check this guide

Los datos de Osstell IDx se cargan automáticamente en su cuenta de OsstellConnect si tiene conexión a Internet. Para conectar su dispositivo a Internet, siga las instrucciones que se indican aquí.

Tenga en cuenta que también puede crear copias de seguridad, por ejemplo, en una memoria USB. Siga estas instrucciones.

• To document an implant failure, go to your patients records. Select the patient, then select the tooth. Click ‘Mark as failed’. Choose the type of failure (early or late failure), fill in the failure date. Choose the reason for failure. Click ‘Mark as failed’.

• You can access the history of the implant failure by navigating to the history tab. Click the tab ‘Failed’ to see all information related to the treatment and the failure.

• A history symbol is displayed on the tooth with a failed implant.

You can record ISQ at abutment level in OsstellConnect, but it is important to follow the correct clinical measurement procedure to obtain accurate values.

How to measure ISQ at abutment level

1. Perform an implant level measurement first, before placing the abutment.
2. Measure again at abutment level during the same session, using a SmartPeg made for abutment level measuring.
3. Determine the offset by noting the difference between implant level and abutment level ISQ. This offset remains stable throughout healing and should be used when interpreting follow-up measurements.
4. For all subsequent visits, measure on the abutment and apply the same offset to understand the true implant ISQ.

How to record the measurement in OsstellConnect:

1.  Go to the patient’s register, select the patient and the implant in the tooth chart. Click ‘Add abutment’, choose the abutment, and save.
2. Select ‘Measure stability’ and choose ‘Abutment’ under Measurement level. Measure on the abutment as you would at implant level and save.
3. To review the stability trend, open the Stability tab and toggle ‘Show abutment’. You can also enable ‘Show details’ to view buccal–lingual and mesial–distal ISQ values.

For a more detailed explanation and clinical guidance, see our blog post here.

Simply navigate to your patient records. Select the patient. Click ‘edit’ on the top right corner. Edit the data and save.

Antes de empezar, asegúrese de que ya tiene instalado Beacon Gateway. Si aún no lo ha instalado, vaya a la sección de su clínica en su cuenta, haga clic en la pestaña «Instruments» (Instrumentos), descargue Gateway e instálelo.

• Conecte Osstell Key a un puerto USB de su ordenador.
• Tome el instrumento en la mano. Ahora se está conectando a OsstellConnect y debería ver el siguiente símbolo en movimiento. Tenga en cuenta que puede tardar unos segundos.
• Cuando está conectado, el símbolo deja de moverse.
• Vaya a los registros de los pacientes.
  • Si se trata de la primera medición, cree un paciente. Rellene los datos del paciente y guarde. Haga clic en «New Treatment» (Nuevo tratamiento) y rellene la información del tratamiento. Haga clic en «Add implant» (Añadir implante), rellene los datos del implante y guarde. Haga clic en «Measure stability» (Medir estabilidad).
  • Si se trata de una medición de seguimiento, seleccione al paciente y, a continuación, el diente en el odontograma. Haga clic en «Measure stability» (Medir estabilidad).
• Mida en la dirección bucolingual. El valor ISQ ya aparece en OsstellConnect.
• Mida en la dirección mesiodistal. El valor ISQ ya aparece en OsstellConnect.
• Rellene la información sobre el tratamiento y guarde.

Yes, simply navigate to your patient records. Select the patient. Select the implant you want to edit on the tooth chart. Select the tab ‘Implant & abutment’. Click on the pen icon to edit. Edit implant data. Save.

Sí, puede exportar todos sus datos a un archivo de Excel para analizarlos más a fondo. Solo tiene que ir a los registros de los pacientes y pulsar «CSV export» (Exportar en CSV). El archivo aparecerá en su carpeta de descargas.

Asegúrese de que los datos exportados se traten de conformidad con la normativa aplicable en materia de protección de datos, como el RGPD o la HIPAA.

Yes, simply navigate to your patient records. Select the patient you would like to delete. Click delete in the upper right corner. Confirm that you want to delete the patient and all data. Please note that it will be permanently removed from your account.

Yes, simply navigate to your patient records. Select the patient. Select the implant. Go to the stability tab. Click on the edit icon by the measurement you would like to delete. Click delete. Please note that the measurement will be permanently removed from the patient chart.